Hyundai Veloster: Specifications
Hyundai Veloster 2011-2017 Service Manual / Dual Clutch Transmission(DCT) System / Specifications
Hyundai Veloster 2011-2017 Service Manual / Dual Clutch Transmission(DCT) System / Specifications
Specifications
|
Model |
D6GF1 |
|
|
Engine |
Gasoline 1.6 GDI |
|
|
Shift ratio |
1st |
3.615 |
|
2nd |
1.955 |
|
|
3rd |
1.303 |
|
|
4th |
0.943 |
|
|
5th |
0.939 |
|
|
6th |
0.743 |
|
|
Reverse |
4.531 |
|
|
Final gear ratio 1 |
4.813 |
|
|
Final gear ratio 2 |
3.667 |
|
| Sensor |
Speed Sensor
▷ Type: Hall effect sensor
▷ Specifications
|
Item |
Specifications |
|
|
Output voltage (V) |
Low |
0.7 |
|
High |
1.4 |
|
| Motor |
Clutch Actuator Motor
▷ Specifications
|
Item |
Specifications |
|
Operating condition (°C) °F |
(20) 68 |
|
Output resistance (mΩ) |
48 ± 7% |
| Inhibitor Switch |
▷ Type: Single signal output type
▷ Specifications
|
Item |
Specifications |
|
Output type |
Combined signal output |
|
Input voltage (V) |
12 |
Tightening torque
|
Item |
N.m |
kgf.m |
lb-ft |
|
TCM mounting bolt/nut |
9.8 ~ 11.8 |
1.0 ~ 1.2 |
7.2 ~ 8.7 |
|
Shift cable bracket bolt |
19.6 ~ 26.5 |
2.0 ~ 2.7 |
14.4 ~ 19.5 |
|
Input speed sensor bolt |
7.8 ~ 9.8 |
0.8 ~ 1.0 |
5.7 ~ 7.2 |
|
Shift lever assembly bolt |
8.8 ~ 13.7 |
0.9 ~ 1.4 |
6.5 ~ 10.1 |
|
Inhibitor switch mounting bolt |
9.8 ~ 11.8 |
1.0 ~ 1.2 |
7.2 ~ 8.7 |
|
Oil drain plug |
58.8 ~ 78.4 |
6.0 ~ 8.0 |
43.2 ~ 57.6 |
|
Oil level plug |
58.8 ~ 78.4 |
6.0 ~ 8.0 |
43.2 ~ 57.6 |
|
Starter motor mounting bolt |
42.2 ~ 53.9 |
4.3 ~ 5.5 |
31.1 ~ 39.8 |
|
Transmission upper mounting bolt (transmission => engine) |
42.2 ~ 53.9 |
4.3 ~ 5.5 |
31.1 ~ 39.8 |
|
Transmission lower mounting bolt (engine => transmission) |
42.2 ~ 53.9 |
4.3 ~ 5.5 |
31.1 ~ 39.8 |
|
Transmission support bracket mounting bolt |
88.3 ~ 107.9 |
9.0 ~ 11.0 |
65.1 ~ 79.6 |
Lubricant
|
Item |
Specified lubricant |
Capacity |
|
Transmission oil |
HA SYN MTF (SK) HD SYN MTF (H.K.SHELL) GS PAO MTF (GS CALTEX) HYUNDAI Genuine transaxle (SAE 75W/85, API GL-4) |
Approx. 1.9 L (0.50 U.S gal., 2.01 U.S.qt.,1.67 Imp.qt.) |
Special Service Tools
Special tools
Tool (Product number and name)
Shape
Function
09200-38001,09200-3N000
Engine support bar (beam)
Remov ...
See also:
Front Strut Assembly. Repair procedures
Replacement
1.
Remove the front wheel & tire.
Tightening torque :
88.3 ~ 107.9N.m(9.0 ~ 11.0kgf.m, 65.1 ~ 79.6lb-ft)
...
Cruise control system
The cruise control system allows you to program the vehicle to maintain a constant
speed without resting your foot on the accelerator pedal.
This system is designed to function above approximately ...
Power Outside Mirror Switch. Repair procedures
Inspection
1.
Disconnect the power door mirror switch module connector from
front door trim panel.
2.
Check for the continuity bet ...
Categories
© 2011-2020 Copyright www.hvmanual.com