Replacement
Front Seat Assembly Replacement
1. |
Remove the front foot cover.
|
2. |
After loosening the front seat assembly mounting
bolts, remove the front seat assembly (A).
Tightening torque
:
34.3 ~ 53.9 N.m (3.5 ~ 5.5 kgf.m, 25.3 ~
39.8 lb-ft)
|
|
3. |
Disconnect the airbag connector (A), seat warmer
connector (B), seat buckle connector (C).
[Driver's]
[Passenger's]
|
4. |
Installation is the reverse of removal.
Seat Mounting Bolt Installation Procedure
• |
Set the into the most rearward position.
Check then each slide is locked, and then Tighten the
front mounting bolt temporarily.
|
• |
Set the seat into most forward position.
Check that each slide is locked, and then Tighten the
rear mounting bolt completely.
|
• |
Set the seat into the most rearward
position. Check the front mounting bolt completely.
|
• |
Check that the seat operates back
and forth smoothy and the locking portion locks properly.
|
|
|
Front Seat Outer Shield Cover Replacement
•
|
When prying with a flat-tip screwdriver,
wrap it with protective tape, and apply protective tape around
the related parts your hands.
|
•
|
Put on gloves to protect your hands.
|
|
1. |
Remove the height knob cap (B).
|
2. |
After loosening the mounting screws, then remove
the height knob (A).
|
3. |
Remove the lock pin (D) after pulling out the recliner
lever (C). And then remove the recliner lever (C) by pulling it.
• |
To see the lock pin (D), pull the
recliner lever (C) as arrow direction .
|
|
|
4. |
Fold the front seat by pushing the seat folding lever
(A).
|
5. |
Unlock the lock pin (C) by pushing the pointed tool
(B) between the seat folding lever (A) and lock pin (C). And then remove
the folding lever (A) by pulling it as arrow direction.
• |
Use the thin and flat shape tool.
|
|
|
6. |
To remove the front shield outer cover (A), disengage
the lock pin (B) and remove the front shield outer cover (A).
|
7. |
Installation is the reverse of removal.
• |
Replace any damaged clips.
|
|
|
Front Seat Outer Shield Cover Replacement
•
|
When prying with a flat-tip screwdriver,
wrap it with protective tape, and apply protective tape around
the related parts your hands.
|
•
|
Put on gloves to protect your hands.
|
|
1. |
Remove the recliner switch (A) and height switch
(B).
|
2. |
To remove the front shield outer cover (A), disengage
the lock pin (B) and remove the front shield outer cover (A).
|
3. |
Disconnect the connector (A).
|
4. |
Installation is the reverse of removal.
• |
Make sure the connector is plugged
in properly.
|
• |
Replace any damage clips.
|
|
|
Seat Back Cover Replacement
•
|
When prying with a flat-tip screwdriver,
wrap it with protective tape, and apply protective tape around
the related parts your hands.
|
•
|
Put on gloves to protect your hands.
|
|
1. |
Remove front seat assembly.
|
2. |
Push the lock pin (B), remove the headrest (A).
|
3. |
Remove the protector (A).
|
4. |
Disconnect the connector (A) and the mounting clips.
|
5. |
To disengage the lock pin (C), lift up the front
seat back board (A) to the arrow direction with holding the bottom place
(B).
• |
Be careful not to damage the lock
pin.
|
|
|
6. |
Push the protecter (A) by the seat back frame.
|
7. |
Remove the protector (A).
|
8. |
Pull out the headrest guides (A) while pinching the
end of the guides, and remove them.
|
9. |
Remove the seat back cover (A) from the frame.
|
10. |
After removing the velcro tape (B) on the front of
seat back and remove the seat back cover (A).
• |
When removing the hog-ring clip,
remove the hog-ring clip with pressing the wire not
to separate the wire from the sponge.
|
|
|
11. |
Installation is the reverse of removal.
• |
Make sure the connector is plugged
in properly.
|
• |
Replace any damage clips.
|
|
|
Seat Cushion Cover Replacement
•
|
When prying with a flat-tip screwdriver,
wrap it with protective tape, and apply protective tape around
the related parts your hands.
|
•
|
Put on gloves to protect your hands.
|
|
1. |
Remove the following items first.
B. |
Front seat outer shield cover
|
|
2. |
Disconnect the connector (A).
|
3. |
Push the protecter (A), and then seat cushion cover
(C) from the frame(B).
|
4. |
Remove the seat cushion cover (A) from the frame.
|
5. |
After removing the velcro tape (B) on the front of
seat cushion and remove the seat cushion cover (A).
• |
When removing the hog-ring clips,
remove the hog-ring clips with pressing the wire not
to separate the wire from the sponge.
|
|
|
6. |
Installation is the reverse of removal.
• |
Make sure the connector is plugged
in properly.
|
• |
Replace any damage clips. s
|
|
|
Seat Frame Replacement
•
|
When prying with a flat-tip screwdriver,
wrap it with protective tape, and apply protective tape around
the related parts your hands.
|
•
|
Put on gloves to protect your hands.
|
|
1. |
Remove the following items first.
B. |
Front seat outer shield cover
|
D. |
Front seat cushion cover
|
|
2. |
After loosening the mounting screw, then remove the
front seat shield inner cover (A).
|
3. |
Disconnect the connector (C).
|
4. |
After loosening the mounting bolts, then disconnect
the seat back frame (A) and seat cushion frame (B).
Tightening torque
:
49.0 ~ 63.7 N.m (5.0 ~ 6.5 kgf.m, 36.2 ~
47.0 lb-ft)
|
|
5. |
Installation is the reverse of removal.
• |
Remove the side air bag for replacing
side air bag installation seat.
|
• |
Before service, be fully aware of
precautions and service procedure relevant to air bag.
(Refer to page RT - Airbag)
|
|
|
Components
1. Headrest
2. Headrest guide
3. Front seat back cover
4. Front seat back heater
5. Front seat back frame
6. Front seat back board
7. Front seat cushio ...
Components
1. Headrest [RH]
2. Headrest guide [RH]
3. Rear seat back cover [RH]
4. Rear seat cushion cover [RH]
5. Cup holder panel assembly
6. Headrest [LH]
7. H ...
See also:
Schematic Diagrams
Circuit Diagram (1)
Circuit Diagram (2)
SRSCM Connector terminal
Pin
Function (Connector A)
Pin
Function (Connector B)
...
Clutch Release Cylinder. Repair procedures
Removal
1.
Drain the brake fluid through the bleed plug (A).
2.
Remove the clutch release cylinder assembly (C) after removing
th ...
Changing tires
1. Park on a level surface and apply the parking brake firmly. 2. Shift the
shift lever into R (Reverse) with manual transaxle or P (Park) with automatic transaxle.
3. Activate the hazard warnin ...