Hyundai Veloster Manuals

Hyundai Veloster: Front Disc Brake. Repair procedures - Brake System - Brake SystemHyundai Veloster: Front Disc Brake. Repair procedures

Hyundai Veloster 2011-2017 Service Manual / Brake System / Brake System / Front Disc Brake. Repair procedures

Removal

1.
Remove the front wheel & tire.
Tightening torque:
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~79.6 lb-ft)
2.
Loosen the hose eyebolt (C) and caliper mounting bolts (B), then remove the front caliper assembly (A).
Tightening torque:
Brake hose to caliper (C):
24.5 ~ 29.4 N.m (2.5 ~ 3.0 kgf.m, 18.1 ~ 21.7 lb-ft)
Caliper assembly to knuckle (B):
78.5 ~ 98.1 N.m (8.0 ~ 10.0 kgf.m, 57.9 ~ 72.3 lb-ft)

3.
Remove the front brake disc by loosening the screws (A).

Replacement

Front Brake Pads
1.
Loosen the guide rod bolt (B) and pivot the caliper (A) up out of the way.
Tightening torque:
21.6 ~ 31.4 N.m (2.2 ~ 3.2 kgf.m, 15.9 ~ 23.1 lb-ft)

2.
Replace pad shim (D), pad retainers (C) and brake pads (B) in the caliper carrier (A).

Inspection

Front Brake Disc Thickness Check
1.
Check the brake pads for wear and fade.
2.
Check the brake disc for damage and cracks.
3.
Remove all rust and contamination from the surface, and measure the disc thickness at 8 points, at least, of same distance (5mm) from the brake disc outer circle.
Brake disc thickness
Standard: 23 mm (0.906 in)
Service limit: 21.4 mm (0.842 in)
Deviation: Less than 0.005 mm (0.0002 in)

4.
If wear exceeds the limit, replace the discs and pad assembly left and right of the vehicle.
Front Brake Pad Check
1.
Check the pad wear. Measure the pad thickness and replace it, if it is less than the specified value.
Pad thickness
Standard value: 10.5 mm (0.41 in)
Service limit: 2.0 mm (0.0787 in)
2.
Check the damage of pad, backing metal and contamination with grease.
Front Brake Disc Runout Check
1.
Place a dial gauge about 5mm (0.2 in.) from the outer circumference of the brake disc, and measure the runout of the disc.
Brake disc runout
Limit: 0.025 mm (0.001 in.) or less (new one)

2.
If the runout of the brake disc exceeds the limit specification, replace the disc, and then measure the runout again.
3.
If the runout does not exceed the limit specification, install the brake disc after turning it 180° and then check the runout of the brake disc again.
4.
If the runout cannot be corrected by changing the position of the brake disc, replace the brake disc.

Installation

1.
Installation is the reverse of removal.
2.
Use a SST (09581-11000) when installing the brake caliper assembly.
3.
After installation, bleed the
(Refer to Brake system bleeding)

Front Disc Brake. Components and Components Location
Components 1. Guide rod bolt 2. Bleed screw 3. Caliper body 4. Caliper carrier 5. Inner pad shim 6. Brake pad 7. Pad retainer ...

Rear Disc Brake. Components and Components Location
Components 1. Guide rod bolt 2. Bleed screw 3. Caliper carrier 4. Caliper body 5. Brake pad 6. Pad retainer ...

See also:

Shopping bag holder
CAUTION Do not hang a bag weighing more than 3 kg (7 lbs.). It may cause damage to the shopping bag holder. Do not hang the frail objects when you drive rough road, the objects may be da ...

Interior Trim. Components and Components Location
Components [RH] 1. Front pillar trim 2. Center pillar lower trim 3. Center pillar upper trim 4. Rear pillar trim 5. Cowl side trim 6. Front door ...

Description and Operation
OBD-II review 1. Overview The California Air Resources Board (CARB) began regulation of On Board Diagnostics (OBD) for vehicles sold in California beginning with the 1988 model year. T ...

Categories

© 2011-2026 Copyright www.hvmanual.com