Hyundai Veloster Manuals

Hyundai Veloster: Specifications - General Information - Driveshaft and axleHyundai Veloster: Specifications

Specification

Engine
TM
Joint type
Max. permissible angle
Outer
Inner
Outer
Inner
Gamma  1.6 GDI
6 MT
BJ#22
TJi#22
46.5°
23°
6 DCT
BJ#24
TJi#22
Gamma  1.6 T-GDI
6 MT
BJ#23
TJi#23
6 A/T
BJ#24
TJi#24

Tightening torque
Item
N.m
kgf.m
lb-ft
Front
Wheel Hub nuts
88.2 ~ 107.8
9.0 ~ 11.0
65.0 ~ 79.5
Driveshaft caulking nut
196.1 ~ 274.5
20.0 ~28.0
144.6 ~ 202.5
Strut assembly to knuckle
137.3 ~ 156.9
14.0 ~ 16.0
101.3 ~ 115.7
Lower arm to knuckle
78.5 ~ 88.3
8.0 ~ 9.0
57.9 ~ 65.1
Tie rod end castle nut
23.5 ~ 33.3
2.4 ~ 3.4
19.4 ~ 24.5
Front caliper to knuckle
78.4 ~ 98.0
8.0 ~ 10.0
57.8 ~ 72.3
Disc fixing screw
4.9 ~ 5.8
0.5 ~ 0.6
3.6 ~ 4.3
Wheel speed sensor & bracket
7.8 ~ 11.8
0.8 ~ 1.2
5.8 ~ 8.7
Rear
Wheel Hub nuts
88.2 ~ 107.8
9.0 ~ 11.0
65.0 ~ 79.5
Rear caliper mounting bolt
63.7 ~ 73.5
6.5 ~ 7.5
47.0 ~ 54.2
Rear axle to torsion beam axle
49.0 ~ 58.8
5.0 ~ 6.0
36.1 ~ 43.3
Disc fixing screw
4.9 ~ 5.8
0.5 ~ 0.6
3.6 ~ 4.3
Wheel speed sensor & bracket
4.9 ~ 5.9
0.7 ~ 1.1
5.1 ~ 8.0

Replace self-locking nuts with new ones after removal.

Lubricants

Engine
Joint type
Lubricants
Quantity
Gamma  1.6 GDI (MT)
BJ#22
RBA
90g
TJ#22
CW09-VX21
135g
Gamma  1.6 GDI (DCT)
BJ#22
RBA
90g
TJi#22
CW09-VX21
135g
Gamma  1.6 T-GDI (MT)
BJ#23
RBA
90g
TJi#23
CW09-VX21
140g
Gamma  1.6 T-GDI (AT)
BJ#24
RBA
100g
TJi#24
CW09-VX21
145g


General Information
...

Special Service Tools
Special Service Tools Tool(Number and Name) Illustration Use 09495-3K000 Band installer Installation of ear type bo ...

See also:

Description and Operation
Operation and Leakage Check Check all of the following items: Component Procedure Brake Booster (A) Check brake operation by applyin ...

Relay Box (Passenger Compartment). Repair procedures
Fuse Inspection 1. Be sure there is no play in the fuse holders, and that the fuses are held securely. 2. Are the fuse capacities for each ...

Overhead Console Lamp. Repair procedures
Inspection 1. Remove the overhead console lamp (map lamp) assembly then check for continuity between terminals. If the continuity is not as specified, replace the map ...

Categories


© 2011-2024 Copyright www.hvmanual.com