Hyundai Veloster Manuals

Hyundai Veloster: Tightening Torque Table Of Standard Parts - General InformationHyundai Veloster: Tightening Torque Table Of Standard Parts

Hyundai Veloster 2011-2017 Service Manual / General Information / Tightening Torque Table Of Standard Parts

Bolt nominal
diameter (mm)
 Pitch (mm)
 Torque Nm (kg.cm, lb.ft)
Head Mark 4
 Head Mark 7

M5
 0.8
 3 ~ 4 (30 ~ 40, 2.2 ~ 2.9)
 5 ~ 6 (50 ~ 60, 3.6 ~ 4.3)
M6
 1.0
 5 ~ 6 (50 ~ 50, 3.6 ~ 4.3)
 9 ~ 11 (90 ~ 110, 6.5 ~ 8.0)
M8
 1.25
 12 ~ 15 (120 ~ 150, 9 ~ 11)
 20 ~ 25 (200 ~ 250, 14.5 ~ 18.0 )
M10
 1.25
 25 ~ 30 (250 ~ 300, 18 ~ 22)
 30 ~ 50 (300 ~ 500, 22 ~ 36)
M12
 1.25
 35 ~ 45 (350 ~ 450, 25 ~ 33)
 60 ~ 80 (600 ~ 800, 43 ~ 58)
M14
 1.5
 75 ~ 85 (750 ~ 850, 54 ~ 61)
 120 ~ 140 (1,200 ~ 1,400, 85 ~ 100)
M16
 1.5
 110 ~ 130 (1,100 ~ 1,300, 80 ~ 94)
 180 ~ 210 (1,800 ~ 2,100, 130 ~ 150)
M18
 1.5
 160 ~ 180 (1,600 ~ 1,800, 116 ~ 130)
 260 ~ 300 (2,600 ~ 3,000, 190 ~ 215)
M20
 1.5
 220 ~ 250 (2,200 ~ 2,500, 160 ~ 180)
 360 ~ 420 (3,600 ~ 4,200, 260 ~ 300)
M22
 1.5
 290 ~ 330 (2,900 ~ 3,300, 210 ~ 240)
 480 ~ 550 (4,800 ~ 5,500, 350 ~ 400)
M24
 1.5
 360 ~ 420 (3,600 ~ 4,200, 260 ~ 300)
 610 ~ 700 (6,100 ~ 7,000, 440 ~ 505)

1.
The torques shown in the table are standard values under the following conditions.
•
Nuts and bolts are made of galvanized steel bar.
•
Galvanized plain steel washers are inserted.
•
All nuts, bolts and plain washers are dry.
2.
The torques shown in the table are not applicable.
•
When spring washers, toothed washers and the like are inserted.
•
If plastic parts are fastened.
•
If self-tapping screws or self-locking nuts are used.
•
If threads and surfaces are coated with oil.
3.
Reduce the torque values to the indicated percentage of the standard value under the following conditions.
•
If spring washers are used : 85%
•
If threads and bearing surfaces are stained with oil : 85%
Emergency Towing
There are three popular methods of towing a vehicle : - The operator loads the vehicle on the back of truck. This is best way of transporting the vehicle. ...

Meaning Of Symbols
There are five primary symbols used to complement illustrations. These symbols indicate the part to apply such materials during service. Symbol Meaning ...

See also:

Overhead Console Lamp. Repair procedures
Inspection 1. Remove the overhead console lamp (map lamp) assembly then check for continuity between terminals. If the continuity is not as specified, replace the map ...

Fuel Pressure Control Valve. Specifications
Specification Item Specification Coil Resistance (Ω) 0.5 [20°C(68°F) ...

License plate light bulb replacement
1. Open the tailgate. 2. Remove the tailgate trim by removing the plastic mounting clips. CAUTION Be careful when removing the plastic mounting clips in cold weather, it may crack. 3. Remove ...

Categories

© 2011-2026 Copyright www.hvmanual.com