Hyundai Veloster Manuals

Hyundai Veloster: Steering Gear box. Repair procedures - Electric Power Steering - Steering SystemHyundai Veloster: Steering Gear box. Repair procedures

Hyundai Veloster 2011-2017 Service Manual / Steering System / Electric Power Steering / Steering Gear box. Repair procedures

Replacement

1.
Remove the front wheel & tire.
Tightening torque :
88.3 ~ 107.9N.m(9.0 ~ 11.0kgf.m, 65.1 ~ 79.6lb-ft)

Be careful not to damage to the hub bolts when removing the front wheel & tire.
2.
Disconnect the stabilizer link (A) with the front strut assembly after loosening the nut.
Tightening torque :
98.1 ~ 117.7N.m(10.0 ~ 12.0kgf.m, 72.3 ~ 86.8lb-ft)

3.
Loosen the nut and then remove the tie-rod end (A) with the front axle.
Tightening torque :
23.5 ~ 33.3N.m(2.4 ~ 3.4kgf.m, 19.4 ~ 24.6lb-ft)

4.
Loosen the nut and then remove the lower arm (A).
Tightening torque :
78.5 ~ 88.3N.m(8.0 ~ 9.0kgf.m, 57.9 ~ 65.1lb-ft)

5.
Loosen the bolt (A) and then disconnect the universal joint assembly from the pinion of the steering gear box.
Tightening torque :
32.4 ~ 37.3N.m(3.3 ~ 3.8kgf.m, 23.9 ~ 27.5lb-ft)

•
Lock the steering wheel in the straight ahead position to prevent the damage of the clock spring inner cable when you handle the steering wheel.
•
Must be replaced with new bolts when assembling. (SEAL-LOCK has been processed)
SEAL-LOCK Specifications: MS721-39 "TYPE-D" Product: ND industries 1193S
6.
Remove the rubber hanger (A).
7.
Loosen the roll rod (A) mounting bolts and nuts.
Tightening torque :
53.9 ~ 63.7N.m(5.0 ~ 6.5kgf.m, 39.8 ~ 47.0lb-ft)

8.
Loosen the bolts & nuts and then remove the front sub frame (A).
Tightening torque :
Sub frame mounting bolt & nut
156.9 ~ 176.5N.m(16.0 ~ 18.0kgf.m, 115.7 ~ 130.2lb-ft)
Sub frame stay mounting bolt
44.1 ~ 53.9N.m(4.5 ~ 5.5kgf.m, 32.5 ~ 39.8lb-ft)

9.
Remove the protector (A) and steering gearbox (B) from the front sub frame by loosening the mounting bolts.
Tightening torque :
58.8 ~ 78.8N.m (6.0 ~ 8.0kgf.m, 43.4 ~ 57.9lb-ft)
[LHD]

[LHD]

[RHD]

[RHD]
10.
Installation is the reverse of the removal.
11.
Check the wheel alignment.
(Refer to SS group - "Tires/Wheels")

Steering Gear box. Components and Components Location
Components 1. Tie-rod end 2. Lock nut 3. Bellows clip 4. Bellows 5. Tie rod 6. Rack bar 7. Dust packing 8. Dust cap 9. Oil seal 10. Pinion plug ...

Restraint (Advanced)
...

See also:

Schematic Diagrams
System circuit diagram Connector pin number Pin No. Discription Remark 1 IG ON   ...

Console. Repair procedures
Replacement Floor Console Replacement [M/T] • A plastic trim tool is recommended, ...

Starting the engine
WARNING Always wear appropriate shoes when operating your vehicle. Unsuitable shoes (high heels, ski boots, etc.) may interfere with your ability to use the brake, accelerator and clutch pedal (i ...

Categories


© 2011-2024 Copyright www.hvmanual.com