Hyundai Veloster Manuals

Hyundai Veloster: Side Impact Sensor (SIS). Repair procedures - SRSCM - Restraint (Advanced)Hyundai Veloster: Side Impact Sensor (SIS). Repair procedures

Hyundai Veloster 2011-2017 Service Manual / Restraint (Advanced) / SRSCM / Side Impact Sensor (SIS). Repair procedures

Removal

Pressure Side Impact Sensor
•
Removal of the airbag must be performed according to the precautions/procedures described previously.
•
Before disconnecting the side impact sensor connector(s), disconnect the side airbag connector(s).
•
Do not turn the ignition switch ON and do not connect the battery cable while replacing the side impact sensor.
1.
Disconnect the battery negative cable, and wait for at least three minutes before beginning work.
2.
Remove the front door trim.
(Refer to the Body group - "Front door")
3.
Disconnect the pressure side impact sensor connector (A) and remove the pressure side impact sensor mounting screws (B).
Side Impact Sensor
1.
Disconnect the battery negative cable and wait for at least three minutes before beginning work.
2.
Remove the door scuff trim.
(Refer to the Body group - "Interior trim")
3.
Remove the center pillar trim.
(Refer to the Body group - "Interior trim")
4.
Disconnect the side impact sensor connector (A).
5.
Loosen the side impact sensor mounting bolt (B) and remove the side impact sensor.

Installation

Pressure Side Impact Sensor
1.
Install the new pressure side impact sensor with the screws (B) then connect the pressure side impact sensor connector (A).
Tightening torque :
1.1 ~ 1.3 N.m (0.11 ~ 0.13 kgf.m, 0.81 ~ 0.96 lb-ft)

•
Use the specified screws only.
2.
Install the front door trim.
(Refer to the Body group - "Front door")
3.
Reconnect the battery negative cable.
4.
After installing the pressure side impact sensor, confirm proper system operation:
A.
Turn the ignition switch ON; the SRS indicator light should be turned on for about six seconds and then go off.
•
You must comply with the specified tightening torques with the tool specified because Pressure – Side Impact Sensors (P-SIS) may be broken or POP-NUT may be rotated.
•
Problems may be occurred in the durability of P-SIS or impact sensing performance may be depreciated if POP-NUT is rotated.
•
The door module must not be transformed because SRSCM judges a impact through the pressure sensor in the door module.
Side Impact Sensor
•
Do not turn the ignition switch ON and do not connect the battery cable while replacing the side impact sensor.
1.
Install the new side impact sensor with the bolt (B) then connect the side impact sensor connector (A).
Tightening torque:
7.0 ~ 9.0 N.m (0.71 ~ 0.92 kgf.m, 5.2 ~ 6.6 lb-ft)

2.
Install the center pillar trim.
(Refer to the Body group - "Interior tirm")
3.
Install the door scuff trim.
(Refer to the Body group - "Interior tirm")
4.
Reconnect the battery negative cable.
5.
After installing the Side Impact Sensor, confirm proper system operation:
A.
Turn the ignition switch ON; the SRS indicator light should be turned on for about six seconds and then go off.

Side Impact Sensor (SIS). Components and Components Location
Components ...

Seat Belt Buckle Switch (BS). Description and Operation
Description The SRSCM shall monitor the status of the driver and front passenger seat belt buckle. The SRSCM provides one pin each for the driver and front passenger seat belt buckle status ...

See also:

Owner’s responsibility
✽ NOTICE Maintenance Service and Record Retention are the owner's responsibility. You should retain documents that show proper maintenance has been performed on your vehicle in accordan ...

Theft-alarm system
This system is designed to provide protection from unauthorized entry into the vehicle. This system is operated in three stages: the first is the "Armed" stage, the second is the " ...

Seat Belt Pretensioner (BPT). Description and Operation
Description The Seat Belt Pretensioners (BPT) are installed inside Center Pillar (LH & RH). When a vehicle crashes with a certain degree of frontal impact, the pretensioner seat belt hel ...

Categories


© 2011-2024 Copyright www.hvmanual.com