Hyundai Veloster: Shift Lever. Repair procedures

Hyundai Veloster 2011-2017 Service Manual / Manual Transaxle System (M6CF1) / Manual Transaxle Control System / Shift Lever. Repair procedures

Removal

Shift Lever Assembly Replacement

1.	Remove the floor Interior console assembly. (Refer to "Interior(Console)" in BD group)

2.	Remove the cover (A).

3.	Remove the select cable (B) by removing the snap pin (A).

4.

Remove the shift lever assembly (B) by removing the bolts (A-4ea).

Tightening torque:

9.8 ~ 14.7 N.m (1.0 ~ 1.5 kgf.m, 7.2 ~ 14.5 lb-ft)

5.	Remove the shift cable (B) by removing the clip (A).

6.	Installation is the reverse of removal.

Select / Shift Cable Replacement

1.	Remove the floor Interior console assembly. (Refer to "Interior(Console)" in BD group)

2.	Remove the cover (A).

3.	Remove the select cable (B) by removing the snap pin (A).

4.

Remove the shift lever assembly (B) by removing the bolts (A-4ea).

Tightening torque:

9.8 ~ 14.7 N.m (1.0 ~ 1.5 kgf.m, 7.2 ~ 14.5 lb-ft)

5.	Remove the shift cable (B) by removing the clip (A).

6.

Remove the retainer (A) and nuts (B-2ea).

Tightening torque:

11.8 ~ 14.7 N.m (1.2 ~ 1.5 kgf.m, 8.7 ~ 10.8 lb-ft)

7.	Disconnect the select and shift cable assembly (B) after removing the pin (A).

8.	Remove the shift cable and select cable at cabin room.

9.	Installation is the reverse of removal.

[Shift / Select Cable Installation Tips]

1.	Install the select and shift cable assembly (B) after removing the pin (A).

2.

Install is the shift cable (A).

At this time, have to disconnect select cable.

3.

Install is the shift lever assembly (A).

Tightening torque:

8.8 ~ 13.7 N.m (0.9 ~ 1.4 kgf.m, 6.5 ~ 10.1 lb-ft)

4.	Shift to the 3th gear position.

5.	Insert the selected cable (A) to the shift lever assembly pin (B).

6.	You have to push in the adjuster (C).

7.	Remove the neutral position pin (D).

8.	Install the snap pin (E).

Inspection

1.	Check the select cable for proper operation and for damage.

2.	Check the shift cable for proper operation and for damage.

3.	Check the boots for damage.

4.	Check the boots for wear abrasion sticking, restricted movement or damage.

5.	Check for the weak or damaged spring.

Adjustment

1.	In neutral position, disjoin select cable (A) from shift lever assembly pin (B).

2.	Disconnect select adjuster (A) to an arrow.

3.	Shift to the 3th gear position.

4.	Adjustment adjuster (B) on select cable (A) as rolling from side to side.

5.	Insert on free load and press the adjuster.

6.

After shifting 2nd gear, cheking the left select gap about 1mm(if not, loop no, 1~5)

If there are still gate blocking in spite of re-adjustment, shift lever assembly stopper stoke must be cheked.

7.	In neutral position, join by clip (A).

Shift Lever. Components and Components Location

Components 1. Shift lever knob & boot assembly 2. Shift lever assembly 3. Shift cable assembly 4. Select cable assembly 5. Retainer ...

Back-up Lamp Switch. Description and Operation

Description Back up lamp switch is pushed by the reverse lug sliding when select arm, and switches the back up lamp. ...

See also:

Front Strut Assembly. Components and Components Location
Components • Tighten under unladen condition • ...

Side repeater light bulb replacement
If the light bulb does not operate, have the vehicle checked by an authorized HYUNDAI dealer. ...

Dimensions Projected
1. These are the dimensions measured when the measurement points are projected from the vehicle's surface, and are the reference dimensions used for used for body ...

Categories

© 2011-2024 Copyright www.hvmanual.com