Hyundai Veloster Manuals

Hyundai Veloster: Passive Occupant Detection System (PODS-F). Repair procedures - SRSCM - Restraint (Advanced)Hyundai Veloster: Passive Occupant Detection System (PODS-F). Repair procedures

Hyundai Veloster 2011-2017 Service Manual / Restraint (Advanced) / SRSCM / Passive Occupant Detection System (PODS-F). Repair procedures

Removal

PODS-F ECU
1.
Disconnect the battery negative cable, and wait for at least three minutes before beginning work.
2.
Remove the front passenger seat assembly.
(Refer to the Body group - "Seat")
3.
Disconnect the PODS-F ECU connector.
4.
Remove the seat cushion cover assembly.
(Refer to the Body group - "Seat")
5.
Remove the seat track assembly.
(Refer to the Body group - "Seat")
PODS-F Mat
1.
Disconnect the battery negative cable, and wait for at least three minutes before beginning work.
2.
Remove the front passenger seat assembly.
(Refer to the Body group - "Seat")
3.
Disconnect the PODS-F mat connector.
4.
Remove the seat cushion assembly.
(Refer to the Body group - "Seat")

Installation

PODS-F ECU
1.
Install the PODS-F ECU equipped seat track assembly.
(Refer to the Body group - "Seat")
2.
Install the seat cushion cover assembly.
(Refer to the Body group - "Seat")
3.
Connect the PODS-F ECU connector.
4.
Install the front passenger seat assembly.
(Refer to the Body group - "Seat")
5.
Reconnect the battery negative cable.
6.
After installing the PODS-F, confirm proper system operation :
A.
Turn the ignition switch ON the SRS indicator should be turned on for about six seconds and then go off.
B.
Telltale lamp will turn on for 4 seconds and be turned off for 3 seconds. After the 7 seconds, it shall remain off if the PODS-F does not require suppression and the passenger airbag is enabled.
Be sure to perform PODS-F reset with GDS after replcacing PODS-F equipped seat cushion.
PODS-F Mat
1.
Install the PODS-F Mat equipped seat cushion assembly.
(Refer to the Body group - "Seat")
2.
Install the front passenger seat assembly.
(Refer to the Body group - "Seat")
3.
Connect the PODS-F mat connector.
4.
Reconnect the battery negative cable.
5.
After installing the PODS-F, confirm proper system operation :
A.
Turn the ignition switch ON the SRS indicator should be turned on for about six seconds and then go off.
B.
Telltale lamp will turn on for 4 seconds and be turned off for 3 seconds. After the 7 seconds, it shall remain off if the PODS-F does not require suppression and the passenger airbag is enabled.
Be sure to perform PODS-F zeroing with GDS after replcacing PODS-F equipped seat cushion.

PODS-F Zeroing procedure

You should perform PODS-F Re-zero procedure after service or replacement about all part of the passenger seat. (Not included full seat assembly)
1.
Ignition “OFF”, connect GDS.
2.
Ignition “ON” & Engine “OFF”, select Airbag system and “PODS-F Reset” mode.
3.
The GDS will show the two PODS-F Zeroing function steps.
(1)
Erase PODS-F diagnostic codes.
(2)
PODS-F initialization.

This step must be done PODS-F re-zero, when the front passenger seat is empty.
4.
The PODS-F initialization procedure will be performed.

Erase the SRSCM diagnostic codes after completing the PODS-F zeroing.
In case of zeroing failure
-
Code 01 : Requestor ID out of range.
-
Code 02 : ECU faults.
-
Code 03 : ODS sensor short to ground.
-
Code 04 : Open between ODS ECU and mat.
-
Code 05 : ODS ECU has not been trimmed.
-
Code 06 : Configuration disabled in ECU calibration.
-
Code 07 : Configuration value out of range.
-
Code 08 : Used in zero Request response only.
-
Code 09 : Algo enabled this ignition cycles.
-
Code 0A : Upper offset value created during the zero process.
-
Code 0B : Lower offset value created during the zero process.
-
Code 0C : Voltage diagnostic
-
Code 0D : The delta of QX_Freq_Low and QX_Freq_High must remain low.
-
Code 0E : Temperature is above O deg C during the zero process.
-
Code 0F : Re-read QX Final compare delta limit. (zero verify)

Passive Occupant Detection System (PODS-F). Components and Components Location
Components ...

Schematic Diagrams
Circuit Diagram (1) Circuit Diagram (2) Circuit Diagram (3) SRSCM Connector terminal Pin Function (Connector A) Pin Function (Co ...

See also:

General Information
General The supplemental restraint system (SRS) is designed to supplement the seat belt to help reduce the risk or severity of injury to the driver and passenger by activating and deploying ...

Body Repair
Interior A Front pillar trim mounting hole (Ø8) Curtain airbag mounting hole (Ø6.6) ...

Schematic Diagrams
Circuit Diagram (1) Circuit Diagram (2) ...

Categories


© 2011-2024 Copyright www.hvmanual.com