Hyundai Veloster Manuals

Hyundai Veloster: Front Repair procedures - Seat Belt - Body (Interior and Exterior)Hyundai Veloster: Front Repair procedures

Replacement

Front Seat Belt Replacement
•
When installing the belt, make sure not to damaged the pretensioner.
1.
Remove the following items first :
A.
Front seat assembly
(Refer to the BD group - "Front Seat")
B.
Front door scuff trim
(Refer to the BD group - "Interior Trim")
C.
Rear door scuff trim [RH]
(Refer to the BD group - "Interior Trim")
2.
Disconnect the battery negative cable, and wait for at least three minutes before beginning work.
3.
The seat belt anchor pretensioner (A) be removed after pushing the lock pin (B) as arrow direction.
[LH]

[RH]

4.
Using a screwdriver or remover, remove the center pillar lower trim (A).
[LH]

[RH]

5.
Using a screwdriver or remover, remove the front seat belt upper anchor cover (A).
[LH]

[RH]

6.
After loosening the mounting bolt, then remove the front seat belt upper anchor (A).
[LH]

Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft )

[RH]

Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft )

7.
After loosening the mounting bolt, then remove the center pillar upper trim (A).
[LH]

[RH]

8.
After disconnecting the pretensioner connector lock pin, remove the seat belt pretensioner connector (A), loosen the mounting bolts, then remove the pretensioner (B).

Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft )

9.
Installation is the reverse of removal.
•
Make sure the connector is plugged in properly.
•
Replace any damage clips.
Front Seat Belt Buckle Replacement
1.
Remove the following items first :
A.
Front seat assembly
(Refer to the BD group - "Front Seat")
2.
After loosening the mounting screws, then remove the front seat track side cover (A).

3.
Remove the seat belt buckle connector mounting clip (A).

4.
After loosening the mounting bolt, then remove the front seat belt buckle (A).

Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)

5.
Installation is the reverse of removal.
•
Replace any damage clips.

Components and Components Location
Components 1. Front seat belt 2. Anchor pretensioner 3. Rear seat belt [RH] 4. Rear seat belt [LH] 5. Rear seat belt buckle [RH] 6. Rear seat belt buckle [LH ...

Rear Repair procedures
Replacement Rear Seat Belt Replacement • When installing the belt, make sure not to dama ...

See also:

Jack and tools
The jack, jack handle, and wheel lug nut wrench are stored in the luggage compartment. Pull up the luggage box cover to reach this equipment. (1) Jack handle (2) Jack (3) Wheel lug nut wrench Ja ...

Roof Trim. Repair procedures
Replacement Sunvisor Replacement • Use a plastic panel removal tool to remove interior t ...

ESC Control Module. Components and Components Location
Components 1. Front - left tube 2. Rear - right tube 3. Rear - left tube 4. Front - right tube 5. MC2 6. MC1 7. ESC control module (HECU) 8. Damper ...

Categories


© 2011-2024 Copyright www.hvmanual.com