Replacement
Roof Garnish Replacement
| •
|
When prying with a flat-tip screwdriver,
wrap it with protective tape, and apply protective tape around
the related parts, to prevent damage
|
| •
|
Put on gloves to protect your hands.
|
| •
|
Take care not to scratch the body surface.
|
|
|
1. |
Using a screwdriver or remover, remove the roof garnish
(A).
|
• |
Replace any damaged roof garnish.
|
|
|
|
2. |
Installation is the reverse of removal.
|
• |
Replace any damaged clips.
|
|
|
Roof Garnish Replacement
| •
|
When prying with a flat-tip screwdriver,
wrap it with protective tape, and apply protective tape around
the related parts, to prevent damage
|
| •
|
Put on gloves to protect your hands.
|
| •
|
Take care not to scratch the body surface.
|
|
|
1. |
Open the movable glass fully.
|
|
2. |
Using a screwdriver or remover, remove the roof garnish
(A).
|
• |
Replace any damaged roof garnish.
|
|
|
|
3. |
Installation is the reverse of removal.
|
• |
Replace any damaged clips.
|
|
|
Front Wheel Guard Replacement
| •
|
When prying with a flat-tip screwdriver,
wrap it with protective tape, and apply protective tape around
the related parts, to prevent damage
|
| •
|
Put on gloves to protect your hands.
|
| •
|
Take care not to scratch the body surface.
|
|
|
1. |
Remove the front tire.
|
|
2. |
After loosening the mounting clips and screws, then
remove the front wheel guard (A).
[LH]
[RH]
|
|
3. |
Installation is the reverse of removal.
|
• |
Replace any damaged clips.
|
|
|
Rear Wheel Guard Replacement
| •
|
When prying with a flat-tip screwdriver,
wrap it with protective tape, and apply protective tape around
the related parts, to prevent damage
|
| •
|
Put on gloves to protect your hands.
|
| •
|
Take care not to scratch the body surface.
|
|
|
2. |
After loosening the mounting clips and screws, then
remove the rear wheel guard (A).
[LH]
[RH]
|
|
3. |
Installation is the reverse of removal.
|
• |
Replace any damaged clips.
|
|
|
Hood Garnish Replacement
| •
|
When prying with a flat-tip screwdriver,
wrap it with protective tape, and apply protective tape around
the related parts, to prevent damage
|
| •
|
Put on gloves to protect your hands.
|
| •
|
Take care not to scratch the body surface.
|
|
|
1. |
Remove the hood insulator pad.
(Refer to the BD group – “Hood”)
|
|
2. |
After loosening the mounting nuts, then remove the
hood garnish (A).
Tightening torque
:
3.9 ~ 4.4 N.m (0.4 ~ 0.45 kgf.m, 2.9 ~ 3.3
lb-ft)
|
|
|
3. |
Installation is the reverse of removal.
|
• |
Replace any damaged clips.
|
|
|
A Pillar Garnish Replacement
| •
|
When prying with a flat-tip screwdriver,
wrap it with protective tape, and apply protective tape around
the related parts, to prevent damage.
|
| •
|
Put on gloves to protect your hands.
|
| •
|
Take care not to scratch the body surface.
|
|
|
1. |
To remove the A pillar garnish (A), loosen the mounting
screw after removing the cap (B).
Tightening torque
:
0.5 ~ 1.0N.m (0.05 ~ 0.1kgf.m, 0.4 ~ 0.7
lb-ft)
|
|
|
2. |
Installation is the reverse of removal.
|
• |
Replace any damaged clips.
|
|
|
Quarter Fixed Glass & Molding Replacement
| •
|
When prying with a flat-tip screwdriver,
wrap it with protective tape, and apply protective tape around
the related parts, to prevent damage.
|
| •
|
Put on gloves to protect your hands.
|
| •
|
Take care not to scratch the body surface.
|
|
|
1. |
Remove the following items.
| A. |
Rear seat
(Refer to the BD group - "Rear Seat")
|
| B. |
Front seat belt lower anchor
(Refer to the BD group - "Front Seat Belt")
|
| C. |
Front door scuff trim
(Refer to the BD group - "Interior Trim")
|
| D. |
Center pillar lower trim
(Refer to the BD group - "Interior Trim")
|
| E. |
Center pillar upper trim
(Refer to the BD group - "Interior Trim")
|
| F. |
Luggage side trim
(Refer to the BD group - "Interior Trim")
|
| G. |
Rear pillar trim
(Refer to the BD group - "Interior Trim")
|
|
|
2. |
After loosening the mounting nuts, then remove the
quarter fixed glass & molding (A).
Tightening torque
:
3.9 ~ 4.4 N.m (0.4 ~ 0.45 kgf.m, 2.9 ~ 3.3
lb-ft)
|
|
|
3. |
Installation is the reverse of removal.
|
• |
Replace any damaged clips.
|
|
|
Rear Spoiler Replacement
| •
|
When prying with a flat-tip screwdriver,
wrap it with protective tape, and apply protective tape around
the related parts, to prevent damage.
|
| •
|
Put on gloves to protect your hands.
|
| •
|
Take care not to scratch the body surface.
|
|
|
1. |
Remove the following items.
| A. |
Tail gate frame upper trim & Tail gate center
trim
(Refer to the BD group - "Tail Gate")
|
| B. |
Tail gate trim
(Refer to the BD group - "Tail Gate")
|
| C. |
Tail gate frame side trim
(Refer to the BD group - "Tail Gate")
|
|
|
2. |
Disconnect the washer nozzle (B) and high mounted
stop lamp connector (A).
|
|
3. |
Loosen the rear spoiler mounting nuts.
Tightening torque :
5.9 ~ 6.4 N.m (0.6 ~ 0.65 kgf.m, 4.3 ~ 4.7
lb-ft)
|
|
|
4. |
Remove the rear spoiler (A).
|
|
5. |
Installation is the reverse of removal.
|
• |
Make sure the connector are connected
in properly.
|
|
• |
Replace any damaged clips.
|
|
|
Replacement
Door Trim Replacement
•
Take care not to scratch the door trim and
other par ...
Components
1. Movable glass assembly
2. Wind deflector assembly
3. Mechanism rail assembly
4. Panoramaroof frame assembly
5. Roller blind support lower assembly
6. R ...
See also:
Specifications
Specification
Smart Key Unit
Items
Specification
Rated voltage
DC 12V
Operating voltage
DC 9 ~ 16V
O ...
Tail Gate. Repair procedures
Replacement
Tail Gate Assembly Replacement
•
When removing and installing the tail gate,
...
Components and Components Location
Components
1. AVN
2. Room Mirror Switch (Blue Link button, Center button, SOS button)
3. Mic
4. Roof Antenna (GPS+CDMA)
5. Telematics unit (TMU)
...
Hyundai Veloster: Body Side Moldings. Repair procedures
Hyundai Veloster 2011-2017 Service Manual / Body (Interior and Exterior) / Exterior / Body Side Moldings. Repair procedures
Rear Door. Repair procedures
Panoramaroof. Components and Components
Location